3DPrinting

17612 readers

191 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: or [email protected]

There are CAD communities available at: [email protected] or [email protected]

Rules

No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
Be respectful, especially when disagreeing. Everyone should feel welcome here.
No porn (NSFW prints are acceptable but must be marked NSFW)
No Ads / Spamming / Guerrilla Marketing
Do not create links to reddit
If you see an issue please flag it
No guns
No injury gore posts

If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 2 years ago

MODERATORS

[email protected]

The Prusa Mk4 has done it again ☹️ (toobnix.org)

submitted 1 day ago by [email protected] to c/[email protected]

11 comments fedilink hide all child comments

This morning I came to work to a perfectly printed set of plates. So I started another instance of the exact same print, went for a swim at the municipal swimming pool nearby, came back to check on it just in case, and it had done the same thing it did on Friday.

This time, nobody was at the office (it's Sunday) so I know nobody monkeyed with the print. Clearly the plate hasn't moved. So those hypotheses are out.

The belts look tight - although the teeth feel a bit chewed up, particularly the table belt. But I doubt this is what caused the slip, as it seems to slip randomly in both directions at the same time.

At this point, I'm placing my bet on the print head coming so close to the edges that it hits the limit(s) when it's unlucky, or it causes the stepper motors' counters to overflow or something - i.e. it hits a firmware bug. The PrusaSlicer software seems very confident that I can print this close to the edges, and indeed the printer does it, but I wonder if it's overly optimistic.

So I bunched up all the plates closer to the center of the bed and re-sliced, so the printer never prints less than ¼ inch from any one edge. Let's see what happens with that.

you are viewing a single comment's thread
view the rest of the comments

[–] [email protected] 3 points 8 hours ago* (last edited 2 hours ago)

Okay so I've readjusted the belts' tension this morning. The X belt was a bit loose and the Y belt was a bit too tight, strangely enough. Both in the green though. So I set them to the middle of the range. Good thing I checked anyway because all the screws on the X motor mount were so loose they were on the verge of letting go completely.

And since I was at it, I cleaned the entire enclosure and re-lubed the rails and the linear bearings.

However, I don't think the printer faulted because of any of this: I checked where the hard limit was in X and Y and found that the nozzle came right at the edge of the previous prints that failed on the left and on the top:

At this point, I'm convinced the printer got lucky twice when it printed that print right, and when it didn't, it was the result of the carriage hitting the limits when the motor(s) overshot the extreme positions a bit. I re-sliced that print to leave some margin with what PrusaSlicer believes are the limits of the printing area and I came to a perfectly printed set of parts today. And the new set I started 2 hours ago seems fine too.

So I think the lesson here is that PrusaSlicer is a bit too optimistic with how large you can print, both in X and Y. It pays not to believe it too much.

EDIT: 6 hours later, another perfect batch. So I think my theory is confirmed.