Morphit
joined 2 years ago
Now, enhance.
Despite the constant negative press covfefe
edited over
What did they edit?
I can still see it.
I think this is all coming from the flap hinges. The hotspots on the leeward part are sparks from the sides. They fall that direction since the re-entry is applying some drag.
The intentionally missing tiles were just on the engine skirt section IIRC. So this isn't necessarily a problem with the main heat shield. The V2 flap design might mitigate it completely. We can't really say much from just one (alleged) image.
Edit: The IFT7 stream stated SN33 has missing tiles spread over the entire heat shield this time.
Edit2: Not going to see anything from IFT7 re-entry.
And then there's shit like this: https://www.amazon.co.uk/Standard-Computer-Quieter2-Quieter2Q-Quieter2D-Black/dp/B099RXXDYT
if you want to use it on the third part mini pc,confirm that the output voltage of your mini pc needs 12V. If the output voltage is lower or higher than 12V and the output current exceed 2A, it will burn your mini pc or cpu.
I think ICQ, AIM and MSN messenger are all dead now. WhatsApp works on Matrix via a bridge. Not sure about other platforms.
This video appeared on my home page and I had to look twice at the thumbnail: The Tomb of Saint Peter Explained
I'm upset that a meme I tried to remake with Unicode box drawing characters lines up terribly in apps: https://lemmy.ca/post/28490027 Shouldn't code blocks render in monospace?
On Lemmy's web frontend it's perfect:
On Connect it looks like this:
On Jerboa it's basically the same:
Eternity does use monospace but the box drawing characters seem to be too wide.
All I can find about it here is one post from a year ago: https://lemmy.ca/post/1492857
2
cross-posted from: https://feddit.uk/post/12276336
Sorry for the crap photos - I just wanted to share these extra keys I added to my Lily58.
I noticed there was a gap in the matrix so I tacked a spare hot-swap socket to the pads on the back of the PCB. That worked with minimal modification to my QMK set-up. I couldn't really use it dangling off some wires so I set out to make an extension that would slot in and be retained by one of the standoffs. I don't have a laser cutter or 3D printer so I just hacked these out of a sheet of ABS plastic following a printed template and glued them up. They're nice and solid and line up really well, despite being rather rough around some of the edges.
I'm finding the 1.5U keys a bit confusing at the moment, swapping them out for 1U keys makes it a bit easier to home my thumbs. These are certainly much easier to access than the outermost keys on the lower row or the keys below the display. I'm thinking they need to be called Lily Pads.
68
cross-posted from: https://feddit.uk/post/12276336
Sorry for the crap photos - I just wanted to share these extra keys I added to my Lily58.
I noticed there was a gap in the matrix so I tacked a spare hot-swap socket to the pads on the back of the PCB. That worked with minimal modification to my QMK set-up. I couldn't really use it dangling off some wires so I set out to make an extension that would slot in and be retained by one of the standoffs. I don't have a laser cutter or 3D printer so I just hacked these out of a sheet of ABS plastic following a printed template and glued them up. They're nice and solid and line up really well, despite being rather rough around some of the edges.
I'm finding the 1.5U keys a bit confusing at the moment, swapping them out for 1U keys makes it a bit easier to home my thumbs. These are certainly much easier to access than the outermost keys on the lower row or the keys below the display. I'm thinking they need to be called Lily Pads.
41
Sorry for the crap photos - I just wanted to share these extra keys I added to my Lily58.
I noticed there was a gap in the matrix so I tacked a spare hot-swap socket to the pads on the back of the PCB. That worked with minimal modification to my QMK set-up. I couldn't really use it dangling off some wires so I set out to make an extension that would slot in and be retained by one of the standoffs. I don't have a laser cutter or 3D printer so I just hacked these out of a sheet of ABS plastic following a printed template and glued them up. They're nice and solid and line up really well, despite being rather rough around some of the edges.
I'm finding the 1.5U keys a bit confusing at the moment, swapping them out for 1U keys makes it a bit easier to home my thumbs. These are certainly much easier to access than the outermost keys on the lower row or the keys below the display. I'm thinking they need to be called Lily Pads.
view more: next ›