Made of 440 grade stainless, was included with parts for a keezer so may be related to beer brewing, 1/4 in dia.
Connections
Puzzle #596
π©π©π©π©
π¨π¨π¨π¨
π¦π¦π¦π¦
πͺπͺπͺπͺ
AbidingOhmsLaw
joined 2 years ago
Wordle 1,317 3/6
β¬β¬β¬β¬π¨
π¨β¬β¬β¬β¬
π©π©π©π©π©
I tell you wut, I prefer propane and propane accessories
Connections
Puzzle #595
π¨π¨π¨π¨
π¦π¦π¦π¦
π©π©π©π©
πͺπͺπͺπͺ
Important! Before you drill, cut, puncture or do anything with them you need to remove the residual gas or they may explode on you!
- obtain or make a valve tool for propane cylinder valves (check youtube).
- screw on a torch head and try to light it to burn off as much as you can EVEN WHEN THE TORCH WONT LIGHT THERE IS STILL PROPANE IN THE CYLINDER
- outside in a well ventilated area remove the torch and press the center valve in to verify that pressure is equalized
- look for the fill valve off center on the top, using the valve tool remove the valve.
- fill the cylinder ALL THE WAY with water, this will force out any remaining gas.
- the cylinder should now be safe to work on
Connections
Puzzle #594
π¦π¦π¦π¦
π¨π¨π¨π¨
π©π©π©π©
πͺπͺπͺπͺ
Strands #326
βUdderly deliciousβ
π΅π΅π΅π‘
π΅π΅π΅
#WhenTaken #330 (22.01.2025)
I scored 836/1000π
1οΈβ£π411 km - ποΈ2 yrs - π₯185/200
2οΈβ£π17.1 km - ποΈ2 yrs - π₯197/200
3οΈβ£π60.4 m - ποΈ6 yrs - π₯193/200
4οΈβ£π253 km - ποΈ12 yrs - π₯170/200
5οΈβ£π275 km - ποΈ47 yrs - π₯91/200
Connections
Puzzle #585
π¨π¨π¨π¨
π©π©π©π©
π¦π¦π¦π¦
πͺπͺπͺπͺ
Connections
Puzzle #584
πͺπͺπͺπͺ
π¦π¦π¦π¦
π©π©π©π©
π¨π¨π¨π¨
wild, got purple first and still donβt know what yellow is
Connections
Puzzle #583
π©π©π©π©
π¨π¨π¨π¨
π¦π¦π¦π¦
πͺπͺπͺπͺ
https://www.nytimes.com/games/connections
Connections
Puzzle #462
π©π©π©π©
π¨π¨π¨π¨
πͺπͺπͺπͺ
π¦π¦π¦π¦
I have a project that is using a Teensy 4.1, the cheep 5v regulator I was using in the project let the magic smoke out for no good reason. I replaced that but now the Teensy boots and runs for about a min then quits. There is a TLV75733P power IC that is supplying the 3v3 and it gets hot then quits supplying power. Since that IC is $0.46 vs a new Teensy 4.1 ~ $40 I want to try and replace it. I have done a bit of SMD work but not tried to remove a tiny chip with a GND pad before so Iβm looking for any tips. The PCB of the Teensy has header pins so I canβt really get good contact to a hot plate to preheat the board.
view more: next βΊ
nasty one today, what the heck yellow?